 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| FUJITSU SEMICONDUCTOR DATA SHEET DS04-33102-1E ASSP ISO/IEC 15693 Compliant FRAM(R) Embedded High-speed RFID LSI FerVID familyTM MB89R119 DESCRIPTION The MB89R119 is an LSI device that has built-in high-speed FRAM and is used for vicinity-RFID. FEATURES * * * * * * * * * * * * * * * Memory capacity of 256 bytes FRAM (including 232 bytes of user area) 4-byte/block configuration, 64 blocks High-speed programming at 37.76 s per block (internal programming time) High-speed data transmission and reception at 26.48 Kbps Fast command supported (data transmission at 52.97 Kbps) (TransponderReader/Writer) Carrier frequency at 13.56 MHz Anti-collision function : 30 tags per second Endurance : 1010 writes to memory Data Retention : 10 years at +55 C 64-bit UID FRAM memory data protection Anti-theft (EAS) command Kill command : to disable tag Compliance with ISO/IEC 15693 (partly not supported*) Compliance with ISO/IEC 18000-3 (Mode 1) (partly not supported*) * : Refer to " NOTES ON USING". FRAM is a registered trademark of Ramtron International Corporation. FerVID family is a trademark of Fujitsu Limited. MB89R119 BLOCK DIAGRAM Analog RF interface Antenna coil Rectifier Clock extractor Power supply voltage control Modulator VDD Anti-collision function Clock I/O Commands Data output Data input Data output Digital control FRAM 256 bytes FRAM access Demodulator Data input R/W 2 MB89R119 MEMORY MAP This section describes the FRAM memory, which is the internal memory of the MB89R119. * FRAM Configuration The FRAM has 232 bytes for use as user area and 24 bytes for use as system area. The FRAM memory areas consist of a total of 64 blocks (58 blocks of user area and 6 blocks of system area). Each block can store 32 bits (4 bytes) of data. The block is the unit used for the writing and reading of FRAM data. The memory map of the FRAM is shown below. * FRAM configuration Area Block No. Details Data read Data write User area (232 bytes) 00H to 39H 3AH 3BH System area (24 bytes) 3CH 3DH 3EH,3FH * : Reserved for future use Blocks "00H" to "39H" are user area. The user area is defined as an area that can be accessed when the corresponding block address is specified. On the other hands, Blocks "3AH" to "3FH" are system area. The system area is defined as an area that can be accessed only with a specific command (request). The system area consists of 6 blocks and contains UID, AFI, DSFID, EAS, IC reference and security status (can write or cannot write) data for individual block. UID, IC reference and RFU is fixed and cannot be updated. AFI, DSFID, and EAS bit are written at the factory, and can be updated and locked (disable to write) with commands. (Only EAS bit cannot be locked.) As shown in above, "3BH" and "3CH" hold the UID, and "3EH" and "3FH" hold the security status information on individual user areas, AFI, and DSFID. As shown in "* Structure of 3DH", "3DH" contains EAS bit, AFI, DFID and IC reference. As shown in the next following figure system areas, "3EH" and "3FH" contains block security status data. * Structure of "3DH" MSB 32 EAS Status User area RFU* UID1 (1 to 32 bit) UID2 (33 to 64 bit) EAS, AFI, DSFID, IC Reference Block security status Yes Yes Yes Yes Yes Yes Yes No No No Limited No LSB 31 Internally used 25 24 IC Reference 17 16 DSFID 98 AFI 1 3 MB89R119 * Structure of "3EH" and "3FH" MSB 32 3EH Block security status (BBS) of user block 1FH AFI Lock Status DSFID Lock Status 31 *** *** RFU* (4 bits) BBS of 39H *** 26 *** LSB 1 BBS of 00H 3FH BBS of 20H * : Reserved for future use The security status of the user area for 58 blocks is stored in the block security status bits in 2 system area blocks of "3EH" and "3FH". A user area is unlocked when the corresponding block security status bit is "0"; it is locked (disable to write state) when the corresponding block security status bit is "1". In the same way, the security status of AFI and DSFID are stored in "AFI Lock Status" and "DSFID Lock Status" respectively. It is possible to read up to 64 blocks data by one command and to write up to 2 blocks data by one command. EAS bit is a single bit, and it is used for setting EAS status. 4 MB89R119 DATA ELEMENT DEFINITION 1. Unique Identifier (UID) The MB89R119 has a 64-bit unique identifier (UID) that complies with ISO/IEC 15693-3. The UID is used to distinguish a transponder from another transponder in the anti-collision algorithm described later. The UID consists of the 3 items shown in the following. * An 8-bit data whose value is always "E0H" (bit 57 to bit 64) * An 8-bit IC manufacturer's code whose value is always "08H", which is defined by ISO/IEC 7816-6/AMI (bit 49 to bit 56) * Unique 48-bit serial number assigned by Fujitsu (bit 1 to bit 48) Among the unique 48-bit serial number assigned by Fujitsu, the 1 byte from bit 41 to bit 48 defines MB89R119 code whose value is "02H". And the 5 bytes from bit 1 to bit 40 define Chip Information. * Structure of UID MSB 64 "E0H" 57 56 49 48 "02H" 41 40 Chip information Unique serial number assigned by Fujitsu IC manufacturer code "08H" LSB 1 5 MB89R119 2. Application Family Identifier (AFI) The application family identifier (AFI) identifies the type of application set by the transponder. The AFI can be written with a command. The AFI is 8-bit data and is stored in the system area of memory (FRAM). The factory default setting of the AFI is "00H". * Types of AFI Application Application Family Sub-Family Application Use Field Example/Note (b8-b5) (b4-b1) "0" X X "0" "1" "2" "3" "4" "5" "6" "7" "8" "9" "A" "B" "C" "D" "E" "F" "0" "0" Y Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y "0", Y All families and sub-families All sub-families of family X Only the Yth sub-families of family X All families of Yth sub-families Transport Financial Identification Telecommunication Medical Multimedia Gaming Data storage Portable files Data identifiers as defined in ISO/IEC 15418 Managed by ISO/IEC JTC1/SC31 Managed by ISO/IEC JTC1/SC31 Managed by ISO/IEC JTC1/SC31 Managed by ISO/IEC JTC1/SC31 Managed by ISO/IEC JTC1/SC31 EAN-UCC system for application identifiers Managed by ISO/IEC JTC1/SC31 ISO/IEC JTC1/SC31 IATA UPU RFU* RFU* RFU* Internet services Mass transit, bus, airline IEP, banking, retail Access control Public telephone, GSM No application preselection Wide applicative preselection * : Reserved for future use Note : Both X value and Y value are "1" to "F". In the status of the AFI_flag setting; * If the AFI is not supported by the transponder, no response to all requests is returned. * If the AFI is supported by the transponder, the response is returned only if the value is in accord with the AFI sent from a reader/writer. 3. Data Storage Format Identifier (DSFID) The data storage format identifier (DSFID) indicates how data is structured in the transponder (LSI memory device). The DSFID can be programmed with a command. The DSFID is 8-bit data and is stored in the system area of memory (FRAM). The factory default setting of the DSFID is "01H". 6 MB89R119 4. Cyclic Redundancy Check (CRC) When a frame is received, reception of correct data--that is, the characters making up the frame is assumed only when the value of the cyclic redundancy check (CRC) code is valid. For error-checking purposes, a 2-byte CRC code value is inserted between data and the EOF signal. The value of CRC code is required from all the data contained between the SOF and CRC field in each frame. Method of calculation is provided in ISO/IEC 13239 and the detail is defined in ISO/IEC 15693-3 and ISO/IEC 18000-3. The initial value of the CRC code provided in ISO/IEC 15693-3 is "FFFFH". The CRC code is transferred, beginning with the lowest-order bit in the lowest-order byte. * CRC bit/byte transition order LSByte LSBit CRC 16 (8 Bits) First transmitted bit of the CRC MSBit LSBit CRC 16 (8 Bits) MSByte MSBit 5. Electronic Article Surveillance (EAS) status EAS status is 1 bit data, which is stored in the system area of memory (FRAM) . The initial value is "1". EAS bit "1" means goods-monitoring status, and EAS bit "0" means that goods-monitoring status is cleared. EAS status can be written by Write EAS command and can be checked "3DH" block (refer to " MEMORY MAP") by Read commands such as Read Signal Block command. Together with Gate type reader/writer, EAS command can support anti-theft security functions. 7 MB89R119 ABSOLUTE MAXIMUM RATINGS Parameter Maximum antenna input current ESD voltage immunity Storage temperature Symbol Imax VESD Tstg Ratings Min 2 - 40 Max 90 + 85 Unit mA0-p kV C Human body model Remarks WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings. RECOMMENDED OPERATING CONDITIONS Parameter Minimum antenna input voltage Antenna input current ASK modulation index (10%) ASK modulation index (100%) ASK pulse width (10%) Symbol VRF IRF m m t1 t2 t3 t1 ASK pulse width (100%) t2 t3 t4 Input frequency Operating temperature Fin Ta Value Min 10 95 6.0 3.0 0 6.0 2.1 0 0 13.553 - 20 Typ 9.2 13.560 Max 11.2 30 30 100 9.44 t1 4.5 9.44 t1 4.5 0.8 13.567 + 85 Unit Vp-p mArms % % s s s s s s s MHz C Remarks WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand. 8 MB89R119 ELECTRICAL CHARACTERISTICS DC characteristics Parameter Internal power supply voltage Load modulation resistance Input capacitance* Internal power consumption Symbol VDP3 RlSW Cant Pd Value Min 3.0 22.8 Typ 3.3 1.0 24.0 100 Max 3.6 25.2 Unit V k pF W Voltage between antennas = 2 Vrms Remarks * : Values are controlled by process monitoring in the wafer. FUNCTION DESCRIPTION 1. Communication from Reader/Writer to Transponder * Modulation method : 10% ASK modulation and 100% ASK modulation are supported. * Modulation rate (m): Modulation rate m is defined as m = (a - b)/(a + b) with reference to the modulated waveform shown below. The values a and b indicate, respectively, the maximum and minimum amplitude of magnetic field transmitted from a reader/writer. * Modulation of the carrier for 10% ASK hr y y t2 t1 t3 b hf a 13.56 MHz 9 MB89R119 * Modulation of the carrier for 100% ASK t3 t1 t4 105 % 95 % 60 % a t2 5% b 13.56 MHz Maximum and minimum values of t1, t2 and t3 are specified in " RECOMMENDED OPERATION CONDITIONS". y is 0.05 (a-b) and the maximum value of hf and hr is 0.1(a-b). 10 MB89R119 * Data rate and bit coding : The MB89R119 supports only 1-out-of-4 mode for bit coding. (Not supports 1-out-of-256 mode.) * 1-out-of-4 mode : In 1-out-of-4 mode, 2-bit signals are coded in a period of 75.52 s as shown in the following. When coding takes place, the data rate is 26.48 Kbps (fc/512). Each signal is transmitted beginning with the lowest bit. * Coding Method in 1-out-of-4 Mode * "00B" pulse position 9.44 s 9.44 s 75.52 s * "01B" pulse position (1 = LSB) 28.32 s 9.44 s 75.52 s * "10B" pulse position (0 = LSB) 47.20 s 75.52 s 9.44 s * "11B" pulse position (0 = LSB) 66.08 s 75.52 s 9.44 s * Data frame : A data frame begins with a start-of-frame (SOF) signal and ends with an end-of-frame (EOF) signal. The MB89R119 is enabled to receive a frame from a reader/writer in 300 s after the MB89R119 has sent a frame to the reader/writer. The MB89R119 is also enabled to receive a frame from a reader/writer within 1 ms after power has been supplied to the MB89R119. * Waveforms of SOF and EOF signals of a frame sent from a reader/writer SOF 9.44 s 9.44 s 9.44 s 37.76 s 37.76 s EOF 37.76 s 9.44 s 9.44 s 11 MB89R119 2. Communication from Transponder to Reader/Writer * Minimum load modulation amplitude (Vlm) : 10 mV (based on ISO/IEC 10373-7) * Load modulation subcarrier frequency (fs) : 423.75 kHz(fc/32) The MB89R119 supports only a 1-subcarrier system. (Not supports 2-subcarrier system.) * Data rate : The MB89R119 supports the following 2 data rate modes : * Low data rate * High data rate One of the 2 data rate modes is specified by the Data_rate_flag (described later) sent from the reader/writer. In low data rate mode, the data rate is 6.62 Kbps (fc/2048); in high data rate mode, it is 26.48 Kbps (fc/512). Also the Fast commands (Custom commands) supports the 2 data rate modes specified by the Data_rate_flag. In Low data rate mode, the data rate is 13.24 Kbps (fc/1024) ; in high data rate mode, it is 52.97 Kbps (fc/256) * Bit coding : The Manchester coding is used for the bit coding. The following figure shows the signals modulated in high data rate mode when standard command is used, and the next following figure shows the same signals when fast command is used. In low data rate mode of both standard commands and fast commands, the number of pulses for subcarrier and data transfer time is 4 times as large as the number in high data rate mode. * Signal waveforms by load modulation in high data rate mode (standard commands) * Logic 0 423.75 kHz subcarrier 18.88 s (modulated) 18.88 s (not modulated) 37.76 s * Logic 1 423.75 kHz subcarrier 18.88 s (not modulated) 18.88 s (modulated) 37.76 s * Signal waveforms by load modulation in high data rate response mode (fast commands) * Logic 0 9.44 s 9.44 s 18.88 s * Logic 1 9.44 s 9.44 s 18.88 s 12 MB89R119 * Data frame : A data frame sent from a transponder starts with a start-of -frame (SOF) signal and ends with an end-of-frame (EOF) signal. The following figure shows the SOF and EOF signals sent in high data rate mode when standard command is used, and the next following figure shows the same signals when fast command is used. In low data rate mode of both standard commands and fast commands, the number of pulses and data transfer time is 4 times as large as the number in high data rate mode, which is the same as explained in the figure below. A reader/writer that has sent a frame to a transponder must be enabled to receive a frame from the transponder within 300 s after the reader/writer has completed sending of the frame. * Waveforms of SOF and EOF signals of a frame sent from a transponder (standard commands) * SOF 423.75 kHz subcarrier 56.64 s 56.64 s 37.76 s * EOF 37.76 s 56.64 s 56.64 s * Waveforms of SOF and EOF signals of a frame sent from a transponder (fast commands) * SOF 423.75 kHz Subcarrier 28.32 s 28.32 s 18.88 s * EOF 423.75 kHz Subcarrier 18.88 s 28.32 s 28.32 s 13 MB89R119 3. FRAM Data Protection if Power Lost During Data Writing If the power to nonvolatile memory is lost while data is being written to it, data may take on unexpected values, possibly adversely affecting system operation. The MB89R119's FRAM is accessed (updated) in byte units. The MB89R119 circle confirms that the level of power supply voltage is sufficient before data is written to each byte. However, since write commands access more than one byte at once a power loss in the middle of write commands may result in a mixture of new written data and still remaining old data. As a result, confirm success of a write command with read command after each write command. 4. Requests/Responses A request is sent from the reader/writer to the transponder. In reply to the request, the transponder sends a response to the reader/writer. Each request, and each response, is transmitted in a single frame. * Structure of requests and responses A request consists of the following 5 fields : * Flag * Command code * Parameter (required or optional depending on the command) * Application data * CRC A response consists of the following 4 fields : * Flag * Parameter (required or option depending on the command) * Application data * CRC Each byte is transferred, beginning with the lowest bit. When two or more bytes are transferred, transfer begins with the lowest one. Set the RFU_flag always to "0". 5. Operating Modes The MB89R119 has the following 2 operating modes : Each mode specifies a different mechanism for how the transponder returns a response in reply to a request from the reader/writer : * Addressed mode The MB89R119 enters addressed mode when the Address_flag is set to "1". In addressed mode, a request includes a UID (the Address_flag is set to "1" simultaneously), and only the transponder that matches the UID in the request returns a response. If no transponder that matches the UID exists, a response is not returned. * Non-Addressed mode The MB89R119 enters non-addressed mode when the Address_flag is set to "0". In non-addressed mode, a request does not include a UID. The transponders that receive the request execute processing and return response in accordance with the command in the request. 14 MB89R119 6. Request Format Figure shows a typical example of the request data format, and Table shows the definition of request flag bits. * Structure of the request frame SOF Flag Command code Parameter Data CRC EOF * Setting of Bit 1 to Bit 4 Bit number Flag name Bit 1 Bit 2 Bit 3 Bit 4 Sub-carrier_flag Data_rate_flag Inventory_flag Protocol_Extension_flag 1/0 0 1 0 1 0 1 0 1 State/Description One subcarrier selected Two subcarriers selected (not supported) Low data rate (6.62 Kbps) selected High data rate (26.48 Kbps) selected Command other than Inventory command selected Inventory command selected Protocol not extended Protocol extended (not supported) Note : "Inventory_flag" of bit3 is determined whether "Inventory command" (select "1") or other command (select "0") is used. 15 MB89R119 * Setting of Bit 5 to Bit 8 (When Inventory command is selected [Inventory_flag = "1"]) Bit number Flag name 1/0 State/Description 0 Bit 5 AFI_flag 1 0 1 0 1 Bit 8 RFU* 0 1 AFI not set AFI set (response when it is in accord with AFI of the transponder) 16-slots (for one or more transponders) 1-slot (for one transponder) Command option not supported (for the command not supporting the Option_flag) Command option supported (not supported) Set to "0" Bit 6 Nb_slots_flag Bit 7 Option_flag * : Reserved for future use * Setting of Bit 5 to Bit 8 (When the command other than Inventory command is selected [Inventory_flag = "0"]) Bit number Flag name 1/0 State/Description Bit 5 Bit 6 Select_flag Address_flag 0 1 0 1 0 1 Bit 8 RFU* 0 1 Command flag decided by the setting of bit 6 and later bits. Select mode (not supported) Non addressed mode (UID not included in the command) Addressed mode (UID included in the command) Command option not supported (for the command not supporting the Option_flag) Command option supported (for only Write, Lock commands) Set to "0" Bit 7 Option_flag * : Reserved for future use 7. Response Format Figure shows a typical example of the response data format, and table shows the definition of the response flag bits. If the error flag is set to "1", an error code field is generated in the response. If the error flag is set to "0", this means no error, and If the error flag is set to "1", this means any error generation. Error codes and their meaning are showed in Table. * Structure of the response frame SOF Flag Parameter Data CRC EOF 16 MB89R119 * Response flag definitions Bit number Flag name Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Error_flag RFU* RFU* Extension_flag RFU* RFU* RFU* RFU* State 0 1 0 0 0 0 0 0 0 Error not found Error found Set to "0" Set to "0" Set to "0" Set to "0" Set to "0" Set to "0" Set to "0" Description * : Reserved for future use * Error code definitions Error code "01" "02" "03" "10" "11" "12" "13" "14" Meaning The specific command is not supported. Example: Command code error Cannot recognize the command. Example: Format error Specific options are not supported. The specified block cannot be used (or was not found). The specified block has already been locked and cannot be locked again. The specified block has already been locked, and its contents cannot be changed. The specified block could not be programmed normally (a write verify error occurred). The specified block could not be locked normally (a lock verify error occurred). 8. Anti-Collision Algorithm The MB89R119 executes an anti-collision sequence loop based on an algorithm that complies with ISO/IEC 15693-3. The anti-collision algorithm is designed to examine the transponders located within reader/writer communication areas on the basis of UID. The reader/writer issues an Inventory request (command) to transponders, and some transponders return responses while other transponders do not according to the algorithm explained in "10. Execution of Inventory Command by a Transponder". 17 MB89R119 9. REQUEST PARAMETER * Request Parameter Settings Set the reader/writer as follows before issuing the Inventory command. * The Nb_slots_flag (bit6), which is a request flag, is set to the desired value : "0" : 16 slots (for plural transponders) "1" : 1 slot (for single transponder) * A mask length and a mask value are added after the command code. * The mask length indicates the significant bits of the mask value. * The mask value is integer bytes of data, transmitted beginning with the lowest bit. If the mask length is not a multiple of 8 (bits), 0 is padded on the MSB side of the mask value so that the data is in units of bytes. The following figure shows an example of the mask value with padding. Since the mask length is 12 bits, the mask value is padded with 4 bits on the MSB side so that the mask data is in units of bytes (2 bytes = 16 bits in this case). If the AFI flag in the request flags is set in the format explained in "* Structure of the request frame of 6 Request Format", an AFI field is added to the format. The command ends with transmission of an EOF signal as described in "1. Communication from Reader/Writer to Transponder". Thereafter, processing in the first slot starts immediately. To proceed to the next slot, the reader/writer sends an EOF signal. * Format of the Command SOF Flag 8 bits Command code 8 bits Mask length 8 bits Mask value 0 to 64 bits CRC 16 bits EOF * Example of the Mask Value with Padding MSB 0000 Pad LSB 0100 1100 1111 Mask value 18 MB89R119 10. Execution of Inventory Command by a Transponder A transponder returns a response to the reader/writer when its UID is equal to the value that consists of the mask value and the number of slots. The mask value is sent in the Inventory command, and the number of slots is determined by the number of times the EOF signal is transmitted. * Algorithm for execution of processing by a transponder The following figure shows the algorithm for the execution of processing by a transponder when an Inventory command is received. The next figure shows the relationship between the UID and the mask value. * Algorithm for Execution of Processing by a Transponder when Inventory Command NbS SN LSB (value, n) & Slot_Frame SN = 0 : Total number of slots (1 or 16) : Current slot number : The "n" least significant bits of value : Concatenation operator : SOF or EOF Nb_slots_flag=1? Yes NbS = 1 SN_length=0 No NbS = 16 SN_length=4 LSB (UID, SN_length + mask length) = LSB (SN, SN_length) & LSB (mask, mask length) ? No Wait (Slot_Frame) No No Yes Response transmission Slot_Frame=SOF? Yes Slot_Frame=EOF? Yes End of processing End of processing SN < NbS-1 Yes SN = SN + 1 No End of processing 19 MB89R119 * Comparison of the mask value and the number of slots with the UID [Inventory command (the side of a reader/writer)] Inventory command includes the mask value and mask length. The mask value is padded with "0" into the higher bit side so to make the byte-unit length (a multiple of 8 bits). Padding Mask value (specified by the Inventory command) 000*** If Inventory command is received, the slot counter is reset to "0". Mask length Slot counter If EOF is received, the increment of the slot counter is started by the transponder. Number of Mask value (no padding) slots Ignored Compared The value is compared with the least significant bits of UID of the transponder. If the value is in accord with the mask value, the response is returned by the transponder. Unique Identifier (UID) [Unique Identifier (the side of a transponder) ] 20 MB89R119 11. Anti-Collision Sequence * Execution of anti-collision sequence A typical anti-collision sequence that is applied when the number of slots is 16 is executed as follows : 1) The reader/writer sends an Inventory command. The Nb_slots_flag of the request flags is set to "0" to specify the number of slots. 2) In slot 0, transponder 1 transmits its response in the time t1_a from the detection of the rising edge of the EOF. In this case no collision occurs and the UID of transponder is received and registered by the reader/ writer. 3) The reader/writer sends an EOF signal to switch to the next slot in the time t2_a after the response 1. 4) In slot 1, transponder 2 and transponder 3 transmits its response in the time t1_a from the detection of the rising edge of the EOF. In this case, the reader/writer cannot recognize the UIDs of the two transponders because the collision occurs, and the reader/writer remembers that a collision was detected in slot 1. 5) The reader/writer sends an EOF signal to switch to the next slot in the time t2_a after the responses. 6) In slot 2, no transponder transmits a response. The reader/writer does not detect any response, and sends an EOF signal to switch to the next slot in the time t3_a from the detection of the rising edge of the EOF. 7) In slot 3, transponder 4 and transponder 5 transmits its response in the time t1_a from the detection of the rising edge of the EOF, and another collision occurs. 8) The reader/writer sends a request (for example, a Read Single Block command, described later) to the transponder 1, which UID was already correctly received. 9) All transponders detect a SOF signal and exit the anti-collision sequence. In this case, since the request is addressed to transponder 1 (Address Mode), only transponder 1 transmits its response. 10) All transponders are ready to receive another request from the reader/writer. If the Inventory command is sent again, the anti-collision sequence starts from slot 0. Note: t1_a, t2_a, t3_a are specified in clause 12. 21 MB89R119 * Example of Anti-Collision Sequence Slot_Counter Reader/Writer (1) SOF Inventory Command Slot 0 EOF (2) Response 1 (3) EOF (4) Slot 1 Response 2 Response 3 MB89R119 Timing Status Slot_Counter Reader/Writer (5) EOF Slot 2 (6) EOF t1_a No Collision Slot 3 (7) Response 4 t2_a t1_a Collision t2_a EOF MB89R119 Response 5 t3_a No response (8) Command transmission SOF Command (to Transponder1) EOF (9) Response (Transponder1) t2_a t1_a t1_a Collision t2_a Timing Status Slot_Counter Reader/Writer MB89R119 Timing Status 22 MB89R119 12. Timing definitions (1)Transponder waiting time before transmitting its response after reception of an EOF from the reader/writer : t1_a After detection of an EOF signal sent from the reader/writer, each transponder must wait for a certain time (t1_a) before sending a response to the reader/writer. t1_a begins at the rising edge of the EOF pulse, and it is defined as following.The minimum value is 4320/fc (= 318.6 s), the nominal value is 4352/fc (= 320.9 s), and the maximum value is 4384/fc (=323.3 s). If the transponder detects a carrier modulation for ASK 100% or 10% within the time t1_a, it shall reset its t1_a timer and wait for further time t1_a before starting to transmit its response to a reader/writer. MB89R119 defines the same waiting time t1_a for Write commands as followings, although the maximum value is not defined in ISO/IEC 15693-3 and ISO/IEC 18000-3 mode1. The minimum value is 4320/fc (= 318.6 s), the nominal value is 4352/fc (= 320.9 s), and the maximum value is 4384/fc (= 323.3 s).Timing conditions for Write command in which the option_flag is "1", has optional field are defined in the command descriptions. (2) Transponder modulation ignore time after reception of an EOF from the reader/writer : tmit After detection of an EOF signal sent from the reader/writer, MB89R119 shall ignore any received 10%, modulation during tmit. tmit starts from the detection of the rising edge of the EOF, and the minimum value is defined as 4384/fc (=323.3 s) + tnrt. tnrt stands for the response time of MB89R119. (3) Reader/writer waiting time before sending a subsequent request : t2_a When the reader/writer has received a response from the transponder to a previous request other than Inventory and Quiet command, it shall wait a time t2_a before sending a subsequent request. The minimum value of t2_a is 309.2 s. It is defined in ISO/IEC 15693-3 and ISO/IEC 18000-3 mode1. When the reader/writer has sent Stay Quiet command or Kill command, which causes no response from the transponder, or MB89R119 does not return any response, MB89R119 can receive a command in 309.2 s from the detection of the rising edge of the EOF. (4) Reader/writer waiting time before sending a request(switching to the next slot) during an Inventory process : t2inv During Inventory process, the reader/writer sends an EOF to switch to the next slot. In this case, the waiting time is defined as follows depending on whether transponders return responses. Waiting time applied when the reader/writer has received one or more responses : t2invwr It is defined in ISO/IEC 15693-3 and ISO/IEC 18000-3 mode1 that when the reader/writer has received one or more responses, the reader/writer must wait until responses from the transponders have been completed (that is, the reader/writer receives an EOF or tnrt passes). After that, the reader/writer must wait as additional t2_a, and then send a 10% or 100% ASK modulated EOF to switch to the next slot. Waiting time applied for when the reader/writer has not received any responses : t3_a When the reader/writer has not received any responses from the transponders, the reader/writer must wait until t3_a passes before sending an EOF signal. In this case, t3_a starts from the rising edge of the last sent EOF. The minimum value of t3_a is defined as shown in the following table. (a) If the reader/writer sends a 10% modulated EOF, the minimum value of t3_a(ASK 10%) is '4384/fc (= 323.3 s) + tnrt' as shown in "* Timing specification". (b) If the reader/writer sends a 100% modulated EOF, the minimum value of t3_a(ASK 100%) is '4384/fc (= 323.3 s) + tsof' as shown in "* Timing specification". tnrt : The nominal response time of transponder tsof : The time duration for transponder to transmit a SOF to the reader/writer - 23 MB89R119 * t3_a for ASK10% and ASK100% signal new command (or EOF signal) no response t1_a t3_a (ASK 100 %) Timing t3_a (ASK 10 %) tsof tnrt Ignore ASK 10 % signal MB89R119 ASK signal handling reset t1_a after receiving ASK 100 % signal ignore ASK 100 % signal possible to receive ASK 10 % signal possible to receive ASK 100 % signal Reader/Writer SOF Inventory command EOF MB89R119 * Timing specification Min t1_a tmit t2_a t2invwr t3_a (ASK10%) t3_a (ASK100%) 4320/fc = 318.6 s 4384/fc(323.3 s)+ tnrt 4192/fc = 309.2 s t2_a + tnrt 4384/fc(323.3 s)+ tnrt 4384/fc(323.3 s)+ tsof Typ 4352/fc = 320.9 s Low data rate : 15708.16 s High data rate : 3927.04 s Fast Low data rate : 7854.08 s Fast High data rate : 1963.52 s Low data rate : 604.16 s High data rate : 151.04 s Fast Low data rate : 302.08 s Fast High data rate : 75.52 s Max 4384/fc = 323.3 s tnrt tsof 24 MB89R119 COMMAND LIST Mandatory and Optional commands defined by ISO/IEC 15693-3 are supported (Partly not supported*). * : Refer to " NOTE ON USING *Comparison between ratings of ISO/IEC 15693 and specification of MB89R119". The following Custom commands are supported : * EAS command designed to monitor and prevent the theft of goods * Write EAS command to write data to the EAS bit * Fast command to respond at double speed compared to standard commands * Kill command to disable the function of tag * Command list Command code Command name Inventory Stay Quiet Read Single Block Write Single Block Lock Block Read Multiple Blocks Write Multiple Blocks Reset to Ready Write AFI Lock AFI Write DSFID Lock DSFID Get System Information EAS Write EAS Kill Fast Inventory Fast Read Multiple Blocks Fast Write Multiple Blocks Command Type Details "01H" "02H" "20H" "21H" "22H" "23H" "24H" "26H" "27H" "28H" "29H" "2AH" "2BH" "A0H" "A1H" "A6H" "B1H" "C3H" "C4H" Mandatory Execute the anti-collision sequence and get UID. Mandatory Enter the Quiet state Optional Optional Optional Optional Optional Optional Optional Optional Optional Optional Optional Custom Custom Custom Custom Custom Custom Read the requested 1 block data in the user area Write the requested 1 block data in the user area Lock (disable to write) the requested 1 block in the user area Read the requested up to 64 blocks data in the user area Write the requested 1 or 2 blocks data in the user area Enter the ready (communication enabled) state Write AFI (Application Family Identifier) data into FRAM. Lock AFI data (disable to write) Write DSFID (Data Storage Format Identifier) data into FRAM Lock DSFID (Data Storage Format Identifier) data (disable to write) Read the system information value (UID, DSFID, AFI, number of bytes per block, number of blocks in user area, and IC information) When EAS bit is "1", reply response code 6 times. Write EAS data (1 bit). Data "1" validates anti-theft/article surveillance, and data "0" invalidates them. Disable the tag Fast response Inventory command Fast response Read Multiple Blocks command Fast response Write Multiple Blocks command 25 MB89R119 COMMAND DESCRIPTION 1. Description of Mandatory Command (1) Inventory command * Description of command The Inventory command executes the anti -collision sequence. Even though an error is detected during execution of this command, a response indicating the error is not returned. The Inventory_flag (bit3) must be set to "1". When the AFI_flag (bit5) in the Inventory command frame is set as "1", the response is returned in the following cases. *The AFI value of the transponder is in accord with the Optional AFI value. *The 4 bits value MSB of the Optional AFI is "0H", and the 4 bits value LSB of the Optional AFI is in accord with the 4 bits value LSB of the transponder. *The 4 bits value LSB of the Optional AFI is "0H", and the 4 bits value MSB of the Optional AFI is in accord with the 4 bits value MSB of the transponder. *The Optional AFI value is "00H". For example, if the AFI value of the transponder is "69H", the response is returned when the Optional AFI value is "69H", "60H", "09H" or "00H". * Command [Request from the reader/writer to the transponder] Command SOF Flag Optional AFI (Inventory) 8 bits * Response [Response from the transponder to the reader/writer] SOF Flag DSFID 8 bits ("00H") 8 bits UID 64 bits CRC 16 bits EOF 8 bits ("01H") 8 bits Mask length 8 bits Mask value 0 to 64 bits CRC 16 bits EOF (2) Stay Quiet command * Description of command On receiving the Stay Quiet command, the transponder enters the quiet state. The transponder does not return any responses, including an error indication. In the quiet state, the transponder does not execute any request for which the Inventory_flag (bit 3) is set and executes only a command for which the Address_flag (bit 6) is set. The transponder exits the quiet state only in the following cases : * The transponder enters the power-off state. * The transponder receives the Reset to Ready command and enters the ready state. * Command [Request from the reader/writer to the transponder] SOF Flag Command (Stay Quiet) UID (necessary) 8 bits * Response [Response from the transponder to the reader/writer] No response 26 8 bits ("02H") 64 bits CRC 16 bits EOF MB89R119 2. Description of Optional Command (1) Read Single Block command * Description of command On receiving the Read Single Block command, the transponder returns the data stored in the specified singleblock to the reader/writer as a response. * Command [Request from the reader/writer to the transponder] Command UID SOF Flag (Read Single Block) (Addressed mode) 8 bits * Response [Response from the transponder to the reader/writer] (a) When Error_flag set SOF Flag 8 bits ("01H") (b) When Error_flag not set SOF Error code 8 bits CRC 16 bits EOF 8 bits ("20H") 64 bits Number of blocks 8 bits CRC 16 bits EOF Flag 8 bits ("00H") Data 32 bits CRC 16 bits EOF (2) Write Single Block command * Description of command On receiving the Write Single Block command, the transponder writes the single-block data included in the request to the specified block. The transponder performs verification after writing and returns an error code if the writing has failed. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the write operation starting after Data 32 bits CRC 16 bits EOF MB89R119 (b) When Error_flag not set SOF Flag 8 bits ("00H") CRC 16 bits EOF (3) Lock Block command * Description of command On receiving the Lock Block command, the transponder locks the data stored in one specified single-block. The transponder performs verification after writing and returns an error code if the writing has failed. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the lock operation starting after CRC 16 bits EOF Flag 8 bits ("00H") CRC 16 bits EOF (4) Read Multiple Blocks Command * Description of command On receiving the Read Multiple Blocks command, the transponder returns the data stored in the specified successive blocks to the reader/writer as a response. Up to 64 blocks of data can be read for one request. The value of the "number of blocks" field specified in the request is the expected number of blocks minus 1. Setting the number of blocks to "06H" makes a request to read 7 blocks. Setting the number of blocks to "00H" makes a request to read 1 block (the request having the same effect as the Read Single Block command). The maximum number of blocks to be set is "3FH". Note : For execution in the addressed mode, the Read Multiple Blocks command must be run without shutting off the RF power supply after obtaining the UID, for example, using the Inventory command. No response may be expected when RF power supply is not stable. 28 MB89R119 * Command [Request from the reader/writer to the transponder] Command UID SOF Flag (Read Multiple Blocks) (Addressed mode) 8 bits * Response [Response from the transponder to the reader/writer] (a) When Error_flag set SOF Flag 8 bits ("01H") (b) When Error_flag not set SOF Error code 8 bits CRC 16 bits EOF 8 bits ("23H") 64 bits First block number 8 bits Number of blocks 8 bits CRC 16 bits EOF Flag Data 32xn bits * CRC 16 bits EOF 8 bits ("00H") *: n is the number of blocks to be responsed. (5) Write Multiple Blocks Command * Description of command On receiving the Write Multiple Blocks command, the transponder writes the successive multiple-block data included in the request to the specified blocks. Up to 2 blocks of data can be written for one request. The transponder performs verification after writing and returns an error code if the writing has failed. The number of blocks specified in the Write Multiple Blocks command is similar to the number of blocks specified in the Read Multiple Blocks command. The value of the number of blocks field specified in the Write Multiple Blocks command is obtained by subtracting 1 from the number of the expected blocks to be written. Setting the number of blocks to "01H" makes a request to write 2 blocks. Setting the number of blocks to "00H" makes a request to write 1 block (the request having the same effect as the Write Single Block command). If at least one of the blocks specified by the command is locked, the transponder does not write any data and, instead, returns an error code. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the write operation starting after Command (Write Multiple Blocks) UID First block Number (Addressed mode) number of blocks Data 32 or 64 bits CRC 16 bits EOF 8 bits ("24H") 64 bits 8 bits 8 bits MB89R119 (b) When Error_flag not set SOF Flag 8 bits ("00H") CRC 16 bits EOF (6) Reset to Ready command * Description of command On receiving the Reset to Ready command, the transponder enters the ready state. * Command [Request from the reader/writer to the transponder] SOF Flag Command (Reset to Ready) 8 bits * Response [Response from the transponder to the reader/writer] (a) When Error_flag set SOF Flag 8 bits ("01H") (b) When Error_flag not set SOF Error code 8 bits CRC 16 bits EOF 8 bits ("26H") UID (Addressed mode) 64 bits CRC 16 bits EOF Flag 8 bits ("00H") CRC 16 bits EOF (7) Write AFI command * Description of command On receiving the Write AFI command, the transponder writes the specified AFI data to FRAM. The transponder performs verification after writing and returns an error code if the writing has failed. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the write operation starting after 30 MB89R119 (a) When Error_flag set SOF Flag 8 bits ("01H") Error code 8 bits CRC 16 bits EOF (b) When Error_flag not set SOF Flag 8 bits ("00H") CRC 16 bits EOF (8) Lock AFI command * Description of command On receiving the Lock AFI command, the transponder locks (write disable) the stored AFI data. The transponder performs verification after writing and returns an error code if the writing has failed. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the lock operation starting after Flag 8 bits ("00H") CRC 16 bits EOF (9) Write DSFID command * Description of command On receiving the Write DSFID command, the transponder writes the specified DSFID data to FRAM. The transponder performs verification after writing and returns an error code if the writing has failed. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the write operation starting after MB89R119 * Command [Request from the reader/writer to the transponder] SOF Flag Command (Write DSFID) UID (Addressed mode) 8 bits * Response [Response from the transponder to the reader/writer] (a) When Error_flag set SOF Flag 8 bits ("01H") (b) When Error_flag not set SOF Error code 8 bits CRC 16 bits EOF 8 bits ("29H") 64 bits DSFID 8 bits CRC 16 bits EOF Flag 8 bits ("00H") CRC 16 bits EOF (10) Lock DSFID command * Description of command On receiving the Lock DSFID command, the transponder locks (write disable) the stored DSFID data. The transponder performs verification after writing and returns an error code if the writing has failed. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the lock operation starting after Flag 8 bits ("00H") CRC 16 bits EOF 32 MB89R119 (11) Get System Information command * Description of command On receiving the Get System Information command, the transponder returns the chip information of UID, AFI, DSFID, and so on to the reader/writer as a response. * Command [Request from the reader/writer to the transponder] SOF Flag Command (Get System Info) UID (Addressed mode) 8 bits * Response [Response from the transponder to the reader/writer] (a) When Error_flag set SOF Flag 8 bits ("01H") (b) When Error_flag not set SOF Flag Information flag 8 bits ("00H") 8 bits Error code 8 bits CRC 16 bits EOF 8 bits ("2BH") 64 bits CRC 16 bits EOF UID 64 bits DSFID 8 bits AFI 8 bits Memory size IC reference 16 bits 8 bits CRC 16 bits EOF The following table shows the definitions of the Information flag. The following figure shows the memory size information included in the response of the System Information. The block size shown in the figure indicates the value that is 1 byte less than the actual block size. Similarly, the number of blocks shown in the figure indicates the value that is 1 block less than the actual number of blocks. * Definition of information flag Bit No. Flag name State Description Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 DSFID AFI Memory size IC reference RFU* RFU* RFU* RFU* 0 1 0 1 0 1 0 1 Set to "0" DSFID is not supported or does not exist. DSFID is supported or exists. AFI is not supported or does not exist. AFI is supported or exists. Memory size information is not supported or does not exist. Memory size information is supported or exists. IC reference information is not supported or does not exist. IC reference information is supported or exists. * : Reserved for future use Note : For MB89R119 set "1" for bit1 to bit4 and set "0" for bit5 to bit8. 33 MB89R119 * Memory size information about a transponder MSB 16 RFU* 14 13 Size of blocks (Number of bytes in 1 block) 98 Number of blocks LSB 1 * : Reserved for future use Note : The memory size of the MB89R119 which is consisted of 58 blocks (4 bytes per block) in the user area is hexadecimal "0339H". 34 MB89R119 3. Custom Command The IC manufacturing code is required to use a Custom command. The IC manufacturing code for the MB89R119 is "08H". (1) EAS command * Description of command On EAS command reception, the transponder returns the response code repeated 6 times after the specified flag ("00H") if the EAS bit is "1" or returns no response if the EAS bit is "0". The EAS command can be executed only when the transponder is in the Ready state. For the response code values, please inquire separately. * Command [Request from the reader/writer to the transponder] SOF Flag 8 bits * Response [Response from the transponder to the reader/writer] SOF Flag Response code 8 bits ("00H") 48 bits (6 times repeat of 8 bits data) CRC 16 bits EOF Command (EAS) 8 bits ("A0H") IC manufacturer code (necessary) 8 bits("08H") CRC 16 bits EOF (2) Write EAS command * Description of command On write EAS command reception, the transponder writes the EAS bit to the FRAM. The transponder performs verification after writing and returns an error code if the writing has failed. The EAS bit must be set to "00H" to cancel anti-theft or goods-monitoring mode. The bit must be set to "01H" to set up the goods-monitoring mode. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the write operation starting after Data CRC EOF 8 bits 16 bits ("00H" or "01H") MB89R119 (b) When Error_flag not set SOF Flag 8 bits ("00H") Data 16 bits CRC 16 bits EOF (3) Kill Command * Description of command On the receiving the Kill command, the transponder is disabled and enters the Dead state. Even if the transponder is moved in the magnetic field (power-on state) again after being removed out of the magnetic field (power-off state), the transponder stays in the Dead state and never respond to any commands from the reader/writer. * Command [Request from the reader/writer to the transponder] SOF Flag 8 bits * Response [Response from the transponder to the reader/writer] (a) When Error_flag set SOF Flag 8 bits (b) When Error_flag not set No response WARNING: The transponder received Kill command is disabled and cannot be used again. (4)Fast Inventory Command * Description of command The Fast Inventory command is the same as the Inventory Command that executes the anti-collision sequence. The datarate in the response is twice as defined in ISO/IEC 15693-3. Even though an error is detected during execution of this command, a response indicating the error is not returned. The Inventory_flag (bit3) must be set to "1". When the AFI_flag (bit5) in the Inventory command frame is set as "1", the response is returned in the following cases. * The AFI value of the transponder is in accord with the Optional AFI value. * The 4 bits value MSB of the Optional AFI is "0H", and the 4 bits value LSB of the Optional AFI is in accord with the 4 bits value LSB of the transponder. * The 4 bits value LSB of the Optional AFI is "0H", and the 4 bits value MSB of the Optional AFI is in accord with the 4 bits value MSB of the transponder. * The Optional AFI value is "00H". For example, if the AFI value of the transponder is "69H", the response is returned when the Optional AFI value is "69H", "60H", "09H" or "00H". Error code 8 bits CRC 16 bits EOF Command(Kill) 8 bits ("A6H") IC Mfg code (necessary) 8 bits ("08H") UID (necessary) 64 bits CRC 16 bits EOF 36 MB89R119 * Command [Request from the reader/writer to the transponder] Command IC manufacturer SOF Flag (Fast Inventory) code (necessary) 8 bits * Response [Response from the transponder to the reader/writer] SOF Flag DSFID 8 bits ("00H") 8 bits UID 64 bits CRC 16 bits EOF 8 bits ("B1H") 8 bits ("08H") Optional AFI 8 bits Mask length 8 bits Mask value 0 to 64 bits CRC 16 bits EOF (5) Fast Read Multiple Blocks Command * Description of command The Fast Read Multiple Blocks command is the same as the Read Multiple Blocks Command that reads the specified successive blocks. The datarate in the response is twice as defined in ISO/IEC 15693. Up to 64 blocks of data can be read for one request. If the Option_flag (bit 7) is "1", the transponder adds block security status information in the response. If the Option_flag (bit 7) is "0", the transponder returns only the data in the specified blocks to the reader/writer. The value of the "number of blocks" field specified in the request is the expected number of blocks minus 1. Setting the number of blocks to "06H" makes a request to read 7 blocks. Setting the number of blocks to "00H" makes a request to read 1 block (the request having the same effect as the Fast Read Single Block command). The maximum number of blocks to be set is "3FH". Note : For execution in the addressed mode, the Fast Read Multiple Blocks command must be run without shutting off the RF power supply after obtaining the UID, for example, using the Inventory command. No response may be expected when RF power supply is not stable. * Command [Request from the reader/writer to the transponder] UID Command IC manufacturer (Addressed SOF Flag (Fast Read code (necessary) mode) Multiple Blocks) 8 bits * Response [Response from the transponder to the reader/writer] (a) When Error_flag set SOF Flag 8 bits ("01H") (b) When Error_flag not set SOF Flag Data Error code 8 bits CRC 16 bits CRC 16 bits EOF EOF 8 bits ("C3H") 8 bits ("08H") 64 bits First block number 8 bits Number of blocks 8 bits CRC 16 bits EOF 8 bits ("00H") 32xn bits * *: n is the number of blocks to be responsed. 37 MB89R119 (6)Fast Write Multiple Blocks Command * Description of command The Fast Write Multiple Blocks command is the same as the Write Multiple Blocks Command, that writes the successive multiple-block data. The datarate in the response is twice as defined in ISO/IEC 15693. Up to 2 blocks of data can be written for one request. The transponder performs verification after writing and returns an error code if the writing has failed. The number of blocks specified in the Fast Write Multiple Blocks command is similar to the number of blocks specified in the Read Multiple Blocks command. The value of the number of blocks field specified in the Fast Write Multiple Blocks command is obtained by subtracting 1 from the number of the expected blocks to be written. Setting the number of blocks to "01H" makes a request to write 2 blocks. Setting the number of blocks to "00H" makes a request to write 1 block (the request having the same effect as the Fast Write Single Block command). If at least one of the blocks specified for data writing is locked, the transponder does not write any data and, instead, returns an error code. If the Option_flag (bit 7) is "0", the transponder shall return its response when it has completed the write operation starting after Data CRC EOF 32 or 64 bits 16 bits Flag 8 bits ("00H") CRC 16 bits EOF 38 MB89R119 4. Command Execution Time (1) Write Multiple Blocks Command Execution Time The minimum time (processing in the address mode) required to complete data writing to all user areas (232 bytes) of the FRAM and verification with the Write Multiple Blocks command is estimated to be 302 ms. (2) Read Multiple Blocks Command Execution Time The minimum time (processing in the address mode) required to complete data reading for all user areas (232 bytes) of the FRAM with the Read Multiple Blocks command is estimated to be 76 ms. In addition, with the Fast Read Multiple Blocks command is estimated to be 41 ms. 39 MB89R119 STATE TRANSITION DIAGRAM * Definition of states Each state of MB89R119 is defined as follows. * Power-Off the state : IF the power-off state, a transponder can not fulfill the function so that the voltage from a reader/writer is underpowered. * Ready state : In the ready state, the MB89R119 can execute all commands from a reader/writer * Quiet state : In the quiet state, the MB89R119 can execute the command from a reader/writer in which the Inventory_flag is not set and the Address_flag is set. * Dead state : In the dead state, the MB89R119 can not execute any command from a reader/writer. As shown in the figure below, the MB89R119 moves from one state to another according to the status of power and by a command. * State transition diagram Power-Off state Out of field In field Out of field Any other command Ready state In field Out of field Kill command Dead state Reset to Ready command Stay Quiet (UID) command All commands Quiet state Any other command where Address_flag is set and where Inventory_flag is not set. 40 MB89R119 NOTES ON USING * Notes on the radio interface - It is the user's responsibility to reduce the effects of the electromagnetic waves produced by the reader/writer. - The user must optimize the shapes of the antenna coils for transponder and reader/writer so that they match the transmission distance and installation space required for the user's application. - If the user intends to access multiple transponders from a reader/writer, the interference between transponders or between the reader/writer and a transponder may degrade communication performance (transmission distance and communication time) . Therefore, a user who intends to design a system using multiple transponders should consider this point. * FRAM reliability Up to 1010 writes to the FRAM memory and 10 years of data retention at + 55 C are guaranteed. For the data retention characteristics at + 150 C or higher, see " SHIPPING METHOD AND RECOMMENDED ASSEMBLY CONDITIONS". * Difference between rating of ISO/IEC 15693 and MB89R119 implementation. The table comparing rating of ISO/IEC 15693 to method of MB89R119 is shown in following. Note that the MB89R119 implementation does not support following ratings. * 1 out of 256 mode data coding * 2-subcarrier 41 MB89R119 * Comparison between ratings of ISO/IEC 15693 and specification of MB89R119 Parameter Communication method Range of modulation rate Data coding Subcarrier Mandatory command Details 10% ASK modulation method 100% ASK modulation method (At using of 10% ASK) 1 out of 256 1 out of 4 1-subcarrier 2-subcarrier Inventory command Stay Quiet command Read Single Block command Write Single Block command Lock Block command Read Multiple Blocks command Write Multiple Blocks command Select command Optional command Reset to ready command Write AFI command Lock AFI command Write DSFID command Lock DSFID command Get System Information command Get Multiple block security status command ISO/IEC 15693 method Correspondence Correspondence 10% to 30% Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence MB89R119 method Correspondence Correspondence 10% to 30% Not correspondence Correspondence Correspondence Not correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence uppermost 64 blocks Correspondence uppermost 2 blocks Not correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Correspondence Not correspondence 42 MB89R119 SHIPPING METHOD AND RECOMMENDED ASSEMBLY CONDITIONS * Shipping Method for the MB89R119 : Please inquire separately for the method used to ship the MB89R119. * The MB89R119 is recommended to be mounted in the following condition to maintain the data retention characteristics of the FRAM memory when the chip is mounted. +175 Temperature [ C] +25 120 Time [min] 43 MB89R119 FUJITSU LIMITED All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of Fujitsu semiconductor device; Fujitsu does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. Fujitsu assumes no liability for any damages whatsoever arising out of the use of the information. Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of Fujitsu or any third party or does Fujitsu warrant non-infringement of any third-party's intellectual property right or other right by using such information. Fujitsu assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that Fujitsu will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. F0507 (c) 2005 FUJITSU LIMITED Printed in Japan |
Price & Availability of MB89R119
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |